Problema con la tarjeta gráfica de un acer aspire SA85

Imagen de josemanuelqm
0 puntos

 Hola, acabo de comprar un acer aspire SA85 con un pentium 4 524.  1GB de RAM. la tarjeta gráfica no he conseguido saber cuál es, aunque las especificaciones que he encontrado por la red hablan de 128 MB compartidos (lo que me dijo el vendedor).  Es un cacharro antiguo ya (viene todavía con el "windoz" Xp, pero total para lo que lo quiero...), pero es barato y mi intención es utilizarlo como servidor de descargas, fundamentalmente.  Mi experiencia es que un portátil con un pentium 4 , 512 MB de rAM y tarjeta de 64 MB compartidos el debian me va suficientemente bien como para ver películas (tengo otro portátil con un centrino y  una tarjeta gráfica de intel integrada de 128 compartidos y va igualmente sin problemas, éste con ubuntu) . Mi sorprersa es que cuando le he instalado el ubuntu dapper a mi nuevo cacharro, las ventanas que abro se mueven a saltos y cuando intento ver una peli va a tirones, vamos que no se puede ver. Evidentemente es cosa de la tarjeta gráfica, pero yo creía que con 128 (aunque sean compartidos) sería suficiente.    Una posibiliodad que se me ocurre es que el driver que ha instalado ubuntu no sea el adecuado, pero no sé por dónde meterle mano. Aquí os pongo lo que me da el dmsg:

 #####################################################################################################

josemanuel@servidor-ubuntu:~/textos$ [4294667.296000] Linux version 2.6.15-23-386 (buildd@rothera) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Tue May 23 13:49:40 UTC 2006
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[4294667.296000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[4294667.296000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[4294667.296000]  BIOS-e820: 0000000000100000 - 000000003bff0000 (usable)
[4294667.296000]  BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS)
[4294667.296000]  BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data)
[4294667.296000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[4294667.296000] 63MB HIGHMEM available.
[4294667.296000] 896MB LOWMEM available.
[4294667.296000] found SMP MP-table at 000f5ad0
[4294667.296000] On node 0 totalpages: 245744
[4294667.296000]   DMA zone: 4096 pages, LIFO batch:0
[4294667.296000]   DMA32 zone: 0 pages, LIFO batch:0
[4294667.296000]   Normal zone: 225280 pages, LIFO batch:31
[4294667.296000]   HighMem zone: 16368 pages, LIFO batch:3
[4294667.296000] DMI 2.3 present.
[4294667.296000] ACPI: RSDP (v000 AWARD                                 ) @ 0x000f7560
[4294667.296000] ACPI: RSDT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bff3040
[4294667.296000] ACPI: FADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bff30c0
[4294667.296000] ACPI: MADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3bff6c80
[4294667.296000] ACPI: DSDT (v001 AWARD  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
[4294667.296000] ACPI: PM-Timer IO Port: 0x1008
[4294667.296000] ACPI: Local APIC address 0xfee00000
[4294667.296000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[4294667.296000] Processor #0 15:4 APIC version 20
[4294667.296000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[4294667.296000] Processor #1 15:4 APIC version 20
[4294667.296000] WARNING: NR_CPUS limit of 1 reached.  Processor ignored.
[4294667.296000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[4294667.296000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[4294667.296000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[4294667.296000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[4294667.296000] ACPI: IRQ0 used by override.
[4294667.296000] ACPI: IRQ2 used by override.
[4294667.296000] ACPI: IRQ9 used by override.
[4294667.296000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[4294667.296000] Using ACPI (MADT) for SMP configuration information
[4294667.296000] Allocating PCI resources starting at 40000000 (gap: 3c000000:c2c00000)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/sda5 ro quiet splash
[4294667.296000] mapped APIC to ffffd000 (fee00000)
[4294667.296000] mapped IOAPIC to ffffc000 (fec00000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[4294667.296000] Detected 3067.684 MHz processor.
[4294667.296000] Using pmtmr for high-res timesource
[4294667.296000] Console: colour VGA+ 80x25
[4294668.959000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[4294668.960000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[4294668.983000] Memory: 963768k/982976k available (1976k kernel code, 18644k reserved, 606k data, 288k init, 65472k highmem)
[4294668.983000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[4294669.043000] Calibrating delay using timer specific routine.. 6136.48 BogoMIPS (lpj=3068242)
[4294669.043000] Security Framework v1.0.0 initialized
[4294669.043000] SELinux:  Disabled at boot.
[4294669.043000] Mount-cache hash table entries: 512
[4294669.043000] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[4294669.043000] CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[4294669.043000] monitor/mwait feature present.
[4294669.043000] using mwait in idle threads.
[4294669.043000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[4294669.043000] CPU: L2 cache: 1024K
[4294669.043000] CPU: After all inits, caps: bfebfbff 20000000 00000000 00000080 0000651d 00000000 00000001
[4294669.043000] mtrr: v2.0 (20020519)
[4294669.043000] CPU: Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 09
[4294669.043000] Enabling fast FPU save and restore... done.
[4294669.043000] Enabling unmasked SIMD FPU exception support... done.
[4294669.043000] Checking 'hlt' instruction... OK.
[4294669.047000] checking if image is initramfs... it is
[4294669.575000] Freeing initrd memory: 6837k freed
[4294669.587000] ACPI: Looking for DSDT ... not found!
[4294669.590000] ENABLING IO-APIC IRQs
[4294669.590000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[4294669.701000] NET: Registered protocol family 16
[4294669.701000] EISA bus registered
[4294669.701000] ACPI: bus type pci registered
[4294669.714000] PCI: PCI BIOS revision 2.10 entry at 0xfbda0, last bus=1
[4294669.714000] PCI: Using configuration type 1
[4294669.714000] ACPI: Subsystem revision 20051216
[4294669.724000] ACPI: Interpreter enabled
[4294669.724000] ACPI: Using IOAPIC for interrupt routing
[4294669.724000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294669.724000] PCI: Probing PCI hardware (bus 00)
[4294669.724000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[4294669.726000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
[4294669.727000] Boot video device is 0000:01:00.0
[4294669.727000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294669.749000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
[4294669.749000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 14 15)
[4294669.749000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 14 15)
[4294669.750000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
[4294669.750000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 14 15)
[4294669.750000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 *6 7 9 10 11 14 15)
[4294669.750000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 14 15)
[4294669.751000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 14 15)
[4294669.753000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294669.753000] pnp: PnP ACPI init
[4294669.756000] pnp: PnP ACPI: found 11 devices
[4294669.756000] PnPBIOS: Disabled by ACPI PNP
[4294669.756000] PCI: Using ACPI for IRQ routing
[4294669.756000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[4294669.789000] PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
[4294669.789000] PCI: Bridge: 0000:00:01.0
[4294669.789000]   IO window: c000-cfff
[4294669.789000]   MEM window: e1000000-e10fffff
[4294669.789000]   PREFETCH window: d8000000-dfffffff
[4294669.789000] audit: initializing netlink socket (disabled)
[4294669.789000] audit(1175452338.788:1): initialized
[4294669.789000] highmem bounce pool size: 64 pages
[4294669.789000] VFS: Disk quotas dquot_6.5.1
[4294669.789000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294669.789000] Initializing Cryptographic API
[4294669.789000] io scheduler noop registered
[4294669.789000] io scheduler anticipatory registered
[4294669.789000] io scheduler deadline registered
[4294669.789000] io scheduler cfq registered
[4294669.790000] isapnp: Scanning for PnP cards...
[4294670.144000] isapnp: No Plug & Play device found
[4294670.160000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[4294671.199000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294671.200000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294671.200000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[4294671.200000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294671.200000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294671.203000] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294671.203000] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294671.203000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294671.203000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294671.203000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294671.203000] mice: PS/2 mouse device common for all mice
[4294671.211000] EISA: Probing bus 0 at eisa.0
[4294671.211000] Cannot allocate resource for EISA slot 1
[4294671.211000] Cannot allocate resource for EISA slot 4
[4294671.211000] EISA: Detected 0 cards.
[4294671.211000] NET: Registered protocol family 2
[4294671.222000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294671.222000] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
[4294671.224000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[4294671.224000] TCP: Hash tables configured (established 131072 bind 65536)
[4294671.224000] TCP reno registered
[4294671.224000] TCP bic registered
[4294671.224000] NET: Registered protocol family 1
[4294671.224000] NET: Registered protocol family 8
[4294671.224000] NET: Registered protocol family 20
[4294671.224000] Using IPI Shortcut mode
[4294671.224000] ACPI wakeup devices:
[4294671.224000] FUTS PCI0 USB0 USB1 USB2 USB3 MAC0 AMR0 UAR1 UAR2 PS2M PS2K
[4294671.224000] ACPI: (supports S0 S3 S4 S5)
[4294671.224000] Freeing unused kernel memory: 288k freed
[4294671.253000] input: AT Translated Set 2 keyboard as /class/input/input0
[4294671.292000] vga16fb: initializing
[4294671.292000] vga16fb: mapped to 0xc00a0000
[4294671.384000] Console: switching to colour frame buffer device 80x25
[4294671.384000] fb0: VGA16 VGA frame buffer device
[4294672.446000] Capability LSM initialized
[4294672.474000] ACPI: Fan [FAN] (on)
[4294672.478000] ACPI: Thermal Zone [THRM] (31 C)
[4294672.893000] SIS5513: IDE controller at PCI slot 0000:00:02.5
[4294672.893000] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 169
[4294672.893000] SIS5513: chipset revision 1
[4294672.893000] SIS5513: not 100% native mode: will probe irqs later
[4294672.893000] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[4294672.893000]     ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
[4294672.893000]     ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:pio
[4294672.893000] Probing IDE interface ide0...
[4294673.412000] Probing IDE interface ide1...
[4294674.084000] hdc: HL-DT-STDVD+-RW GSA-H21N, ATAPI CD/DVD-ROM drive
[4294674.390000] ide1 at 0x170-0x177,0x376 on irq 15
[4294674.401000] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[4294674.401000] Uniform CD-ROM driver Revision: 3.20
[4294674.437000] SCSI subsystem initialized
[4294674.439000] ACPI: bus type scsi registered
[4294674.439000] libata version 1.20 loaded.
[4294674.440000] sata_sis 0000:00:05.0: version 0.5
[4294674.440000] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 177
[4294674.440000] sata_sis 0000:00:05.0: Detected SiS 180/181 chipset in SATA mode
[4294674.440000] ata1: SATA max UDMA/133 cmd 0xD800 ctl 0xDC02 bmdma 0xE800 irq 177
[4294674.440000] ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xE402 bmdma 0xE808 irq 177
[4294674.645000] ata1: dev 0 cfg 00:0c5a 49:2f00 82:346b 83:7d01 84:4023 85:3468 86:3c01 87:4023 88:407f 93:0000
[4294674.645000] ata1: dev 0 ATA-7, max UDMA/133, 312581808 sectors: LBA48
[4294674.647000] sata_get_dev_handle: SATA dev addr=0x50000, handle=0xdffe8920
[4294674.650000] ata1: dev 0 configured for UDMA/133
[4294674.652000] sata_get_dev_handle: SATA dev addr=0x50000, handle=0xdffe8920
[4294674.655000] scsi0 : sata_sis
[4294674.857000] ata2: no device found (phy stat 00000000)
[4294674.857000] scsi1 : sata_sis
[4294674.857000]   Vendor: ATA       Model: ST3160812AS       Rev: 3.AA
[4294674.857000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[4294674.863000] Driver 'sd' needs updating - please use bus_type methods
[4294674.864000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[4294674.864000] SCSI device sda: drive cache: write back
[4294674.865000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[4294674.866000] SCSI device sda: drive cache: write back
[4294674.866000]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[4294674.923000] sd 0:0:0:0: Attached scsi disk sda
[4294675.291000] usbcore: registered new driver usbfs
[4294675.291000] usbcore: registered new driver hub
[4294675.292000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[4294675.292000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 185
[4294675.292000] ohci_hcd 0000:00:03.0: OHCI Host Controller
[4294675.316000] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[4294675.316000] ohci_hcd 0000:00:03.0: irq 185, io mem 0xe1104000
[4294675.369000] hub 1-0:1.0: USB hub found
[4294675.369000] hub 1-0:1.0: 3 ports detected
[4294675.470000] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 193
[4294675.470000] ohci_hcd 0000:00:03.1: OHCI Host Controller
[4294675.493000] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[4294675.493000] ohci_hcd 0000:00:03.1: irq 193, io mem 0xe1100000
[4294675.546000] hub 2-0:1.0: USB hub found
[4294675.546000] hub 2-0:1.0: 3 ports detected
[4294675.647000] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 201
[4294675.647000] ohci_hcd 0000:00:03.2: OHCI Host Controller
[4294675.670000] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[4294675.670000] ohci_hcd 0000:00:03.2: irq 201, io mem 0xe1101000
[4294675.723000] hub 3-0:1.0: USB hub found
[4294675.723000] hub 3-0:1.0: 2 ports detected
[4294675.825000] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 209
[4294675.825000] ehci_hcd 0000:00:03.3: EHCI Host Controller
[4294675.825000] PCI: cache line size of 128 is not supported by device 0000:00:03.3
[4294675.826000] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[4294675.826000] ehci_hcd 0000:00:03.3: irq 209, io mem 0xe1102000
[4294675.826000] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[4294675.826000] hub 4-0:1.0: USB hub found
[4294675.826000] hub 4-0:1.0: 8 ports detected
[4294675.950000] Probing IDE interface ide0...
[4294676.541000] usb 3-2: new full speed USB device using ohci_hcd and address 2
[4294676.542000] Attempting manual resume
[4294676.562000] EXT3-fs: mounted filesystem with ordered data mode.
[4294676.579000] kjournald starting.  Commit interval 5 seconds
[4294682.384000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294683.852000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294683.893000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[4294683.920000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 18 (level, low) -> IRQ 217
[4294683.921000] eth0: Identified chip type is 'RTL8169SC/8110SC'.
[4294683.921000] eth0: r10001.02, the Linux device driver for Realtek Ethernet Controllers at 0xec00, 00:19:21:67:26:06, IRQ 217
[4294683.922000] eth0: Auto-negotiation Enabled.
[4294684.987000] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 217
[4294685.116000] input: PC Speaker as /class/input/input1
[4294685.267000] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[4294685.298000] intel8x0_measure_ac97_clock: measured 50788 usecs
[4294685.298000] intel8x0: clocking to 48000
[4294685.590000] Real Time Clock Driver v1.12
[4294686.080000] eth0: 10Mbps Half-duplex operation.
[4294686.080000] Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter
[4294686.080000] Driver version:1.02
[4294686.080000] Released date:2006/02/23
[4294686.080000] Link Status:Linked
[4294686.080000] Link Speed:10Mbps
[4294686.080000] Duplex mode:Half-Duplex
[4294686.080000] I/O Base:0xEC00(I/O port)
[4294686.080000] IRQ:217
[4294686.212000] Linux agpgart interface v0.101 (c) Dave Jones
[4294686.218000] agpgart: Detected SiS 661 chipset
[4294686.236000] agpgart: AGP aperture is 128M @ 0xd0000000
[4294686.244000] ts: Compaq touchscreen protocol output
[4294686.564000] parport: PnPBIOS parport detected.
[4294686.564000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[4294686.576000] Initializing USB Mass Storage driver...
[4294686.576000] scsi2 : SCSI emulation for USB Mass Storage devices
[4294686.576000] usb-storage: device found at 2
[4294686.576000] usb-storage: waiting for device to settle before scanning
[4294686.576000] usbcore: registered new driver usb-storage
[4294686.576000] USB Mass Storage support registered.
[4294687.196000] lp0: using parport0 (interrupt-driven).
[4294687.279000] Adding 1020088k swap on /dev/sda7.  Priority:-1 extents:1 across:1020088k
[4294687.515000] EXT3 FS on sda5, internal journal
[4294687.717000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294687.717000] md: bitmap version 4.39
[4294687.809000] NET: Registered protocol family 10
[4294687.809000] lo: Disabled Privacy Extensions
[4294687.809000] IPv6 over IPv4 tunneling driver
[4294688.139000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294688.922000] cdrom: open failed.
[4294690.341000] kjournald starting.  Commit interval 5 seconds
[4294690.341000] EXT3 FS on sda6, internal journal
[4294690.341000] EXT3-fs: mounted filesystem with ordered data mode.
[4294690.498000] NTFS driver 2.1.25 [Flags: R/O MODULE].
[4294690.537000] NTFS volume version 3.1.
[4294691.385000] ACPI: Power Button (FF) [PWRF]
[4294691.385000] ACPI: Power Button (CM) [PWRB]
[4294691.385000] ACPI: Sleep Button (CM) [FUTS]
[4294691.467000] ibm_acpi: ec object not found
[4294691.487000] pcc_acpi: loading...
[4294691.584000]   Vendor: Generic   Model: USB SD Reader     Rev: 1.00
[4294691.584000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294691.617000] sd 2:0:0:0: Attached scsi removable disk sdb
[4294691.617000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[4294691.625000]   Vendor: Generic   Model: USB CF Reader     Rev: 1.01
[4294691.625000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294691.658000] sd 2:0:0:1: Attached scsi removable disk sdc
[4294691.658000] sd 2:0:0:1: Attached scsi generic sg2 type 0
[4294691.664000]   Vendor: Generic   Model: USB SM Reader     Rev: 1.02
[4294691.664000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294691.698000] sd 2:0:0:2: Attached scsi removable disk sdd
[4294691.698000] sd 2:0:0:2: Attached scsi generic sg3 type 0
[4294691.705000]   Vendor: Generic   Model: USB MS Reader     Rev: 1.03
[4294691.705000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294691.737000] sd 2:0:0:3: Attached scsi removable disk sde
[4294691.737000] sd 2:0:0:3: Attached scsi generic sg4 type 0
[4294691.737000] usb-storage: device scan complete
[4294698.365000] ppdev: user-space parallel port driver
[4294698.559000] eth0: no IPv6 routers present
[4294698.700000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[4294698.700000] apm: overridden by ACPI.
[4294699.075000] Bluetooth: Core ver 2.8
[4294699.075000] NET: Registered protocol family 31
[4294699.075000] Bluetooth: HCI device and connection manager initialized
[4294699.075000] Bluetooth: HCI socket layer initialized
[4294699.108000] Bluetooth: L2CAP ver 2.8
[4294699.108000] Bluetooth: L2CAP socket layer initialized
[4294699.121000] Bluetooth: RFCOMM socket layer initialized
[4294699.121000] Bluetooth: RFCOMM TTY layer initialized
[4294699.121000] Bluetooth: RFCOMM ver 1.7
[4295149.105000] ibm_acpi: ec object not found
[4297229.691000] ISO 9660 Extensions: RRIP_1991A
[4298955.141000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.141000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.141000] ide: failed opcode was: unknown
[4298955.141000] end_request: I/O error, dev hdc, sector 64
[4298955.141000] Buffer I/O error on device hdc, logical block 16
[4298955.158000] end_request: I/O error, dev hdc, sector 68
[4298955.158000] Buffer I/O error on device hdc, logical block 17
[4298955.160000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.160000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.160000] ide: failed opcode was: unknown
[4298955.160000] end_request: I/O error, dev hdc, sector 64
[4298955.160000] Buffer I/O error on device hdc, logical block 16
[4298955.176000] end_request: I/O error, dev hdc, sector 68
[4298955.176000] Buffer I/O error on device hdc, logical block 17
[4298955.180000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.180000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.180000] ide: failed opcode was: unknown
[4298955.180000] end_request: I/O error, dev hdc, sector 64
[4298955.180000] Buffer I/O error on device hdc, logical block 16
[4298955.196000] end_request: I/O error, dev hdc, sector 68
[4298955.196000] Buffer I/O error on device hdc, logical block 17
[4298955.198000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.198000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.198000] ide: failed opcode was: unknown
[4298955.198000] end_request: I/O error, dev hdc, sector 64
[4298955.198000] Buffer I/O error on device hdc, logical block 16
[4298955.214000] end_request: I/O error, dev hdc, sector 68
[4298955.214000] Buffer I/O error on device hdc, logical block 17
[4298955.216000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.216000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.216000] ide: failed opcode was: unknown
[4298955.216000] end_request: I/O error, dev hdc, sector 64
[4298955.216000] Buffer I/O error on device hdc, logical block 16
[4298955.232000] end_request: I/O error, dev hdc, sector 68
[4298955.232000] Buffer I/O error on device hdc, logical block 17
[4298955.265000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.265000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.265000] ide: failed opcode was: unknown
[4298955.265000] end_request: I/O error, dev hdc, sector 64
[4298955.281000] end_request: I/O error, dev hdc, sector 68
[4298955.282000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.282000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.282000] ide: failed opcode was: unknown
[4298955.282000] end_request: I/O error, dev hdc, sector 64
[4298955.298000] end_request: I/O error, dev hdc, sector 68
[4298955.301000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.301000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.301000] ide: failed opcode was: unknown
[4298955.301000] end_request: I/O error, dev hdc, sector 64
[4298955.316000] end_request: I/O error, dev hdc, sector 68
[4298955.318000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.318000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.318000] ide: failed opcode was: unknown
[4298955.318000] end_request: I/O error, dev hdc, sector 64
[4298955.334000] end_request: I/O error, dev hdc, sector 68
[4298955.337000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
[4298955.337000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
[4298955.337000] ide: failed opcode was: unknown
[4298955.337000] end_request: I/O error, dev hdc, sector 64
[4298955.408000] end_request: I/O error, dev hdc, sector 68
[4298955.586000] end_request: I/O error, dev hdc, sector 64
[4298955.765000] end_request: I/O error, dev hdc, sector 68

######################################################################################

donde los mensajes de error últimos provienen del cdrom cuando intentaba ver la pelicula . No creo que sea ésta la causa de mis problemas, ya que al correr el "xine-check", obtenía estos mensajes que confirmaban mis sospechas:

 josemanuel@servidor-ubuntu:~/textos$ xine-check
Please be patient, this script may take a while to run...
[ good ] you're using Linux, doing specific tests
[ good ] looks like you have a /proc filesystem mounted.
[ good ] You seem to have a reasonable kernel version (2.6.15-23-386)
[ good ] intel compatible processor, checking MTRR support
[ good ] you have MTRR support and there are some ranges set.
[ good ] found the player at /usr/bin/xine
[ hint ] multiple xine executables found in your PATH
         I have found more than one occurance of 'xine' in your PATH:
         /usr/bin/X11/xine
         /usr/bin/xine
         You have probably installed xine-ui more than once, or the directory
         where you have installed xine occurs more than once in your PATH.
         Technically, this is not really a problem, but it's probably
         somewhat confusing, as it's not obvious, which xine you're using.
         You should probably uninstall the copies that you don't use...
         Further tests assume, you're using /usr/bin/X11/xine
         press <enter> to continue...

[OUCH!!] no xine-config on this machine.
         This means that xine-lib is either not installed
         or it is installed in a very unusual place.
         So you should probably install xine-lib before running xine-check...
         press <enter> to continue...

[ hint ] unable to determine plugin directory
         I could not determine your plugin directory. That would be much easier
         if you had xine-config installed (see message above)...
         Note that I could not check your xine plugins.
         press <enter> to continue...

[ good ] /dev/cdrom points to /dev/hdc
[ good ] /dev/dvd points to /dev/hdc
[ good ] DMA is enabled for your DVD drive
[ good ] found xvinfo: X-Video Extension version 2.2
[ hint ] Your X server doesn't support YV12 overlays.
         That means xine will have to do color space transformation and scaling
         in software, which is quite CPU intensive. Maybe upgrading your
         X server will help here.
         If you have an ATI card, you'll find accelerated X servers on
         http://www.linuxvideo.org/gatos/
         press <enter> to continue...

[ hint ] Your X server doesn't support YV12 overlays.
         That means xine will have to do color space transformation and scaling
         in software, which is quite CPU intensive. Maybe upgrading your
         X server will help here.
         If you have an ATI card, you'll find accelerated X servers on
         http://www.linuxvideo.org/gatos/
         press <enter> to continue...

[ hint ] Your X server doesn't have any XVideo support...
         XVideo is an X server extension introduced by XFree86 4.x. This
         extension provides access to hardware accelerated color space
         conversion and scaling, which gives a great performance boost.
         If you have a fast (>1GHz) machine, you may be able to watch all
         kinds of video, anyway. You will waste lots of CPU cycles, though...
         press <enter> to continue...

################################################3

 

 

 ¿Alguien me puede hacer una sugerencia?¿ o intento descambiar el caharro y me compro algo más potente? ( no sé si será posible porque ya le he particionado obviamente el disco duro, arrinconando el windoz ...).

 

Gracias por adelantado y un saludo

 

                                                 Jose Manuel
 

 

Imagen de josemanuelqm
+1
0
-1

 Bueno, ya que ningún "alma caritativa"  se apiada de mí, os doy más datos sobre la tarjeta gráfica. los he obtenido con el windoz (ni me había acordado de que lo tenía...), ya que lo que dice cesarix87 de leerlo en la esquinita de la pantalla al comienzo durante varios segundos aquí no vale (los de ACER han puesto su logo en el pantallazo inicial). Bueno ésta es (el driver):

 

   SiS Mirage Graphics Driver

   version 6.14.10.3680

 

  Además, ya que estaba con el windoz y por curiosidad le he instalado el DivX y he visto la peli: se ve sin problemas, luego el windoz configura la tarjeta mejor. No iremos a consentir que ubuntu no sea capaz de hacer lo  mismo que el windoz...¿o sí?

Para mí sería una gran desilusión... 

 

                        José Manuel 

+1
0
-1